Panel-mounted surge protection
Whole House Surge Protection in Brooklyn
A surge protector at your panel guards every circuit, from the refrigerator and boiler controls to TVs, computers and EV chargers.

Kings County Electric installs whole house surge protection in Brooklyn homes, brownstones and multifamily buildings. A whole house surge protective device, mounted at or beside your electrical panel, catches voltage spikes before they reach the outlets and appliances throughout the house.
Modern homes are full of electronics that a single surge can damage: appliance control boards, boiler and heat pump electronics, smart thermostats, garage and gate openers, computers and the charger in an electric car. Power strips at the outlet only protect what is plugged into them. Panel-level surge protection protects everything on the system, and it pairs naturally with the other residential electrician services we provide.
Every Circuit Covered
Protection starts at the panel, not the power strip.
Listed Devices
UL 1449 listed surge protective devices only.
Proper Installation
Short leads and correct breaker sizing for real performance.
Layered Protection
Panel device plus point-of-use protection where it matters.
Where Power Surges Come From
When people think of surges, they picture lightning. Lightning can cause severe surges, but most surges are smaller and far more frequent. They come from the utility switching loads on the grid, from power coming back after an outage, and from inside your own building every time a large motor or compressor cycles on and off.
Small, repeated surges rarely cause a dramatic failure. Instead, they wear down sensitive electronics over time, which is why an appliance control board or a furnace igniter can fail years earlier than it should. In Brooklyn row houses and apartment buildings that share service with neighbors and elevators, internal surges are a daily fact of life.
A whole house surge protector limits those spikes at the panel and diverts the excess energy to ground. It works best on a solid grounding system, so we check your grounding and bonding as part of the install. If your panel is old or full, we may recommend an electrical panel upgrade at the same time.
What a whole house surge protector helps protect
- Refrigerators, washers, dryers and dishwashers
- Boiler, furnace and heat pump controls
- Central and split air conditioning systems
- TVs, computers, routers and home offices
- Smart home hubs, cameras and doorbells
- EV chargers and the car’s onboard charger
Type 1, Type 2 and Type 3 Surge Protection
Surge protective devices are grouped by where they are installed. A good plan usually combines a whole house device with point-of-use protection for your most sensitive equipment.
| Type | Where it goes | What it protects against | Best for |
|---|---|---|---|
| Type 1 | Line side of the main service, ahead of the main breaker | External surges entering from the utility service | Buildings with exposed service runs or where the utility side needs protection |
| Type 2 | Load side, at or in the main electrical panel | External surges that get past the service and internal surges from loads | Most homes: the standard whole house surge protector |
| Type 3 | At the outlet, as a plug-in strip or receptacle | Remaining small spikes close to the equipment | Computers, TVs and home office gear, as a second layer |
When comparing devices, look at the surge current rating, the voltage protection rating (lower means less voltage gets through), and an indicator light that shows the protection is still active. Newer editions of the National Electrical Code require surge protection when a dwelling service is installed or replaced. We will tell you how the NYC Electrical Code applies to your job.
How We Install Whole House Surge Protection
Surge protectors only perform as well as they are installed. We mount the device as close to the panel as possible and keep the conductors short and straight, because long leads reduce how well the device clamps a spike. We connect it to a properly sized breaker or the service terminals according to the manufacturer and the code, and we verify the grounding electrode system.
Installation is usually a single visit with a brief planned power shutdown. We finish by checking the indicator, labeling the breaker, and showing you how to tell at a glance that the protection is active. Devices that take a major hit are designed to be replaced, and we can swap one quickly.

Protect Everything You Plug In
One surge protector at the panel covers every circuit in the house, the appliances you can’t plug into a power strip included.
Add it on its own, or pair it with a panel upgrade, rewiring project or EV charger install. Call for a free, upfront quote anywhere in Brooklyn.
Whole House Surge Protection FAQ
What Brooklyn homeowners ask us about surge protectors. Call (646) 450-9911 for answers specific to your home.
Is whole house surge protection worth it?
For most homes, yes. The device costs far less than a single appliance control board, a boiler control or an EV charger, and it protects all of them at once. It also reduces the slow wear that repeated small surges cause on electronics over time.
Does a whole house surge protector replace power strips?
Not entirely. The panel device stops the large spikes. Point-of-use surge protectors at computers, TVs and home office equipment add a second layer for small residual spikes. Together they give the best protection.
Will a surge protector protect my home from lightning?
No device can guarantee protection from a direct lightning strike. A whole house surge protector greatly reduces damage from surges that travel in on the power lines from nearby strikes and grid events, which are far more common than direct hits.
How much does whole house surge protection cost in Brooklyn?
Cost depends on the device, whether your panel has room for its breaker, the condition of your grounding system, and whether the work is combined with other electrical projects. We give you a free, upfront quote after checking your panel.
How long does a whole house surge protector last?
Surge protectors wear as they absorb surges. Many last for years, while a large event can use one up sooner. That is why we install devices with a status indicator, so you can see when protection is still active and when it needs replacement.
Do I need an electrician to install a surge protector?
Yes. A whole house surge protector connects inside your main panel or at the service, which is licensed electrical work in New York City. Installation quality, especially lead length and grounding, directly affects how well it works.
Can you add surge protection to an apartment or co-op?
Usually, yes, at the apartment’s own panel, with building approval where required. In multifamily buildings we can also protect the main service and common systems for owners and boards.
Book Whole House Surge Protection
Tell us about your home and your panel. We will reply with next steps and a free, upfront quote for surge protection.
Open 24 hours Monday through Saturday. Sunday 8:30 AM to 2 PM. 347 Rogers Ave, Brooklyn, NY 11225.